Hardware

nanoMoCo boards and the OpenMoCo Development Framework are now available!  nanoMoCo is a complete single-axis stepper driver/controller that is compatible with the Arduino IDE and development framework.  Want more than one axis? MoCoBus allows real-time synchronization with up to 253 total devices - which can be other nanoMoCo devices, or anything which can speak the MoCoBus protocol.  

Project Chronos, a DIY motion control platform for timelapse.
Project Chronos 1.0 is no longer supported and replaced by Project Chronos 2.0

Please check my project page on sourceforge.net for more information on this DIY full featured timelapse system
https://sourceforge.net/p/projectchronos/home/Project%20Chronos%20Home/
Facebook
https://www.facebook.com/ProjectChronos2/photos_stream
Website
http://thechronosproject.com/

miniE is an engine sketch to provide control over a single stepper motor and camera, using an Arduino and DFRobot LCD Keypad shield. It is an open design providing all the necessary features to do shoot-move-shoot or continuous timelapse with a built-in UI. The 1st version of the code was inspired by the OpenMoCo Engine by C.A. Church and is basically based on it - Thank you for your great work and help! The project has evolved since its first version and is now a standalone software/hardware solution. The aim of the system is to be as flexible as possible. For this lightweight engine, full system control is possible out in the field without extra hardware. 

Version 1.1 (fully non-blocking)

After you've selected the motor type appropriate for your project, it's time to move to the next stage of building your first motion control rig: gear selection.  Unless you've bought a motor with an attached gearbox (and even if you have, in some cases), it's time to figure out exactly how you intend transfer power from the motor into your final motion.  Just like the process of selecting a motor, you'll need to first examine your requirements, and how they might change over time.  In this article, we'll walk through the basic process of selecting the proper gear train, and the different factors that should affect your decision.

The basic factors to consider are: building vs. buying, complexity, gear ratio, precision, and braking requirements.

The DollyShield is an adaptation of the Arduino Motor Shield v3 that provides directional PWM control of two DC motors, at up to 1A of current each.  In addition to the motor drivers, it also provides a stereo plug with dual opto-coupled outputs for direct camera control, a 2x16 LCD, five user input buttons, and four auxilliary inputs or outputs through two stereo jacks.  It is designed to provide an inexpensive and easy-to-use interface for two-axis motion control integrated with a camera.

One of the more daunting tasks for your first motion control project is to decide on which kind of motor you need.  The right choice in motor can save you money and effort in the long run, not to mention increase your chances of getting the shots you're looking for.  Before selecting your motor, you need to first examine what your requirements are, and how they might change over time.  In this article we'll walk you through the process of selecting a motor for a motion control rig and the different factors that should play into the decision.

The basic principles you'll need to consider in motor selection, outside of cost, are: timeframe (how long your shoots will run for), power requirements, and repeatability.

Introduction

While we spend a lot of our time focusing on stepper motors, we'd rather not leave out brushed DC motors!  It's hard to beat them for their simplicity and low cost.  When it comes to drivers for DC motors, there are a lot of options - from cheap $15 PWM drivers that can be found on eBay, to professional units that can cost up to several thousand dollars.  I've been using the Pololu JRK 21v3 driver with great success.  It offers rarely found in drivers several times its cost.  At approximately $50 USD it might seem a little pricey until you explore the options it gives you. In this article, we'll cover how to make an easy-to-use carrier board for the JRK 21v3 that will let you hook it right up into an OpenMoco system, and especially the dedicated hand-held engine model, while still retaining all of the features and flexibility of the driver.